Essential Plumber Tips for Bathtub Installation
Essential Plumber Tips for Bathtub Installation
Blog Article
On this page down the page you might get a good deal of brilliant tips related to How to Install a Bathtub.
Mounting a bath tub isn't specifically rocket science, however it does need solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a moderately challenging task. If the old tub is conveniently available, the project can move easily; if you have to open a wall surface to eliminate the old tub as well as position the brand-new tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. See to it you have certified on your own for the work as well as are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed project, it is much better to think about employing one before you start. Possibilities are you may need an expert plumber to make tube connections.
This write-up will certainly help you set up a new tub in your restroom if you have already acquired a new tub as well as do not require to change the setup of your previous water supply pipes.
Your tools and material list must comprise the following:
Preparing for the Installment
To start with, the supporting frame supplied with the bath ought to be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final position.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome as a result of the restricted gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to moving on to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the called for position. The wooden boards are valuable in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bath tub up until the level reviews level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the supply of water as well as check all joints and brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as likewise examine the overflow outlet and also the normal outlet for leaks.
Ultimately, repair the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the tub has been utilized at the very least once as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The former type ought to be connected to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break an inflexible seal, causing the water to pass through the wall between the bath as well as the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently available on the market. It is suggested to fit the floor tiles making use of water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very inquisitive about How to Install a Bathtub and I'm hoping you enjoyed the page. Please take the time to share this post if you liked it. Thank-you for going through it.
Get it sorted! Report this page